Save 21% £7,899.00 £6,208.80 (Inc VAT)
£5,174.00 (Ex VAT). Shipping calculated at checkout.
The Manley Variable MU has been Manley`s best selling product for many years. It is one of the very few compressors that has become a real standard in Mastering studios and contributed to most hit records over the last decade and probably the next. "MU" is tube-speak for gain, and Variable MU is the registered trademark for this limiter compressor. It works by using the "remote cut-off" or re-biasing of a vacuum tube to achieve compression. The precious vintage Fairchild 670 also uses this technique and is one of few all-tube compressor to do so, that we know of. Even the side-chain has glowing rectifier bottles. The unique 5670 dual triode is at the centre of the peak-reducing and compression action constantly being re-biased by the vacuum tube rectified side-chain control voltages which cause this tube to smoothly change its gain.
The COMPRESS mode is soft-knee 1.5 to 1 ratio while the sharper knee LIMIT mode starts at 4 to 1 and moves to a more dramatic ratio of 20 to 1 when limiting over 12dB. Interestingly, the knee actually softens as more limiting is used. Distortion can be creatively used by turning up the Input and turning down the Output while using very little or no compression. See the gain reduction curves here!
You might notice that the Variable MU Limiter Compressor has a ganged input control, but do not jump to conclusions that it is mono-unfriendly. Track away! There are separate threshold and output controls to make compensations with plus you can always adjust your individual source levels elsewhere, right? The advantage of the stereo input control becomes dramatically clear when you switch to LINK mode, and that`s what our Variable MU Limiter Compressor does better than anything else: final mix, 2-track, or mastering limiting and compression.
The Works version of the Manley Variable MU contains additional options/modifications listed below.
Backstory: The newer Variable Mu units use 5670 tubes instead of the 6386. By now the availability of the original USA GE 6386 is poor; we don`t have any left at all, and what we do have are not usable due to noise, microphonics, bad side-to-side match, etc.
So does the 5670 sound different? Well, up to about 6db of limiting it`s about the same. After that point, the 5670 version tends to sound more "squashed" than the original 6386 version. Some like it better, some don`t - depends on what you`re trying to do.
To solve all these problems, Paul came up with a really good solution: the T-Bar Mod. This uses a pair of 6BA6 pentodes wired as single triodes to replace each dual triode 5670 (or 6386). The 6BA6 T-Bar Mod is the preferred system to use in the Manley Variable Mu® for reasons of ability to perfectly match each phase-halve section and each stereo set, ability to select for lo-noise and lo-microphonic sets for a low cost, and because the action of the 6BA6`s so closely resemble the smooth 6386 limiting curves.
This modification opens the door to stereo encoding and decoding as well as exciting image enhancement processing capabilities. For instance, setting to compress only the in-phase information allows the augmentation of the stereo image as the out-of-phase content is left untouched. Or, conversely, if you need a "more-mono" mix for broadcast, or vinyl-cutting for instance, you can set it to kill off more of the out-of-phase info which leaves more in-phase material in the final result. Read more about the MS Mod on page 12 of the Owner`s Manual.
In order to add both M-S and the HP SC mods, we move the power switch to the rear panel and install both channels` HP SC switch to the centre hole where the power switch was. The M-S switches then flank this switch.
UK Mainland – Orders over £99 qualify for FREE standard shipping (1-3 working days) We also offer a range of chargeable express shipping options for next working day, pre 12pm, pre 10.30am, Saturday deliveries and deliveries on a specific date. Our main UK courier is DPD.
UK Non Mainland – Not eligible for free shipping. These areas include (but are not limited to) Isle of Man, Isle of Wight, Isles of Scilly, Jersey, Guernsey, Northern Ireland, Orkney, Scottish Highlands and Shetland. Shipping costs for these ares will be calculated at checkout.
International/Export – Delivery charges will be calculated at checkout. All orders that are in stock we aim to dispatch from our warehouse within 48 hours. We ship all orders outside of the UK, NI, Isle of Man, Channel Islands via Fedex. All prices and delivery charges are exclusive of VAT for export. The customer is responsible to pay for any additional duties and charges.
Read more on our shipping information page
If you have an SX Pro account:
Login, go to your Order History find the invoice for the item you want to return, click on the invoice then select “Request a return”, then select the item and quantity you want to return. This will take you to the returns form, simply fill it in and wait for our response.
No account, or orders prior to 31/03/2021
Simply fill out the returns form on this page and wait for our response.
